Menu
(Mon-Thurs 8am-5pm, Fri 8am-4pm)
Fast Delivery & Reliable Service
Specialists With 20+ Years Experience
Independent & Impartial Advice
Trusted by Customers, Rated 4.5/5
(1)

Mizar Submersible Dirty Water Pump

Product Code: 24101017
Product Code: 24101017
Stock Status: In Stock
Order within to get it by .
In Stock
Prefer to pay by phone?
Call 0333 050 3748 for quick and secure payment with our friendly team.
You may also need

Mizar 30 & 60 Stainless Steel Submersible Drainage Pumps

Compact Pumps for Cellar, Sump and Rainwater Drainage

The Mizar 30 and Mizar 60 are compact stainless steel submersible pumps for removing clean water and lightly dirty drainage water containing small suspended particles. Suitable for cellars, basement sumps, garages, collection tanks and rainwater transfer, they offer a choice of pumping capacities for domestic, trade and light industrial applications.

Their top-discharge design directs the outlet upwards, making hose routing convenient where space around the pump is restricted. An AISI 304 stainless steel outer casing, suction cover and strainer are combined with a technopolymer impeller and an oil-lubricated mechanical seal.

Choose the Mizar 30 for a maximum flow of 150 litres per minute and a maximum head of 8 metres, or the Mizar 60 for up to 175 litres per minute and 10 metres maximum head.

Both models are available in 110V and 230V, with manual or automatic pendant-float operation, and are supplied with a 10-metre rubber power cable.

304 Stainless Steel | 10mm Free Passage | Top Discharge | Manual or Automatic | 110V or 230V

Why Choose a Mizar Drainage Pump?

  • Corrosion-resistant stainless steel construction: AISI 304 casing and intake components provide a durable construction for compatible drainage water.
  • Compact top-discharge layout: The upward-facing outlet helps keep the discharge arrangement close to the pump.
  • Choice of water-level control: Select manual operation for attended pumping or an automatic version with a pendant float switch.
  • Oil-lubricated mechanical seal: The sealing arrangement protects the motor, with vegetable-oil-based biodegradable fluid used for lubrication.
  • Built-in motor protection: Integral thermal overload protection and an internal capacitor are included in the single-phase motor design.

Mizar 30 or Mizar 60: Which Model Should You Choose?

Mizar 30 – General Drainage and Water Transfer

The Mizar 30 has a 0.25kW motor output, a maximum flow of 150 litres per minute and a maximum head of 8 metres.

It is a practical choice for cellar sumps, collection tanks and general property drainage where its performance matches the required duty. Choose the Mizar 30 when it can deliver the flow you need through your intended hose or pipework.

Mizar 60 – Additional Flow and Delivery Head

The Mizar 60 increases motor output to 0.45kW, with a maximum flow of 175 litres per minute and a maximum head of 10 metres.

Its additional head is useful where water must be lifted higher or the discharge arrangement creates more resistance. It also delivers more water than the Mizar 30 at comparable points on the published performance curves.

Both models have a 10mm free passage. Choosing the Mizar 60 increases pumping performance, not the size or type of solids the pump can handle.

Model Comparison and Technical Specifications

Specification Mizar 30 Mizar 60
Pump type Submersible drainage pump Submersible drainage pump
Motor output, P2 0.25kW / 250W 0.45kW / 450W
Maximum flow rate 150 litres/minute 175 litres/minute
Maximum flow rate in m³/hour 9m³/hour 10.5m³/hour
Maximum head 8 metres 10 metres
Voltage options 110V or 230V 110V or 230V
Electrical supply Single phase, 50Hz Single phase, 50Hz
Operation options Manual or automatic Manual or automatic
Automatic level control Pendant float switch Pendant float switch
Discharge size 1¼-inch / 32mm nominal 1¼-inch / 32mm nominal
Discharge position Top Top
Maximum free passage 10mm 10mm
Liquid temperature range 0–35°C 0–35°C
Maximum immersion depth 5 metres 5 metres
Power cable length 10 metres 10 metres
Pump body diameter 154mm 154mm
Dry weight – manual version 4.9kg 5.6kg
Dry weight – automatic version 5.2kg 5.8kg
Motor protection rating IP68 IP68
Insulation class F F
Thermal overload protection Integral Integral

Motor output is not the same as electrical input consumption. Use the selected pump’s electrical nameplate when checking supply requirements or sizing a transformer or generator.

The body diameter is not a minimum sump dimension. Allow additional room for the float switch, discharge connection, cable routing and maintenance access.

Manual or Automatic Operation

Manual Versions

A manual Mizar starts and stops when its electrical supply is switched on and off. Choose this version for supervised pump-out tasks or use with a correctly specified external control system.

A manual pump does not automatically respond to changing water levels. The operator or external controls must prevent operation without sufficient water.

Automatic Versions

Automatic models are fitted with a pendant float switch that rises and falls with the water, starting and stopping the pump through each drainage cycle.

The float needs sufficient room to move freely. It must not catch against chamber walls, discharge pipework or cables.

The stopping level can be adjusted through the float-cable arrangement in accordance with the operating instructions. Always check the completed installation to ensure the pump starts and stops correctly while maintaining the required water level for safe operation.

What Type of Water Can the Standard Mizar Pump?

The standard Mizar 30 and 60 are intended for clean water and lightly dirty drainage water with small suspended particles up to 10mm.

Typical duties include removing rainwater or seepage from sumps, transferring water from collection tanks and supplying low-pressure garden watering where the required duty falls within the pump’s performance range.

The 10mm free passage is not a sewage or slurry rating. These pumps should not be used for wipes, long fibres, thick sludge, concentrated sediment or abrasive sand-laden water.

The standard models use 304 stainless steel construction. This page does not cover the separate Mizar VOX or Mizar/S 316 stainless steel versions.

What’s Included?

Your selected Mizar 30 or Mizar 60 is supplied with a 10-metre rubber power cable, carrying handle and intake strainer.

Automatic versions include the pendant float switch. Manual versions do not include automatic water-level control.

Discharge hose and hose clips are available separately. Henry Pumps can help select the correct hose and any additional connection fittings required for your installation.

Select the required model, voltage and operating type before adding the pump to your basket.

Installation and Maintenance

Keep the installation clear of loose sediment and ensure the pump cannot draw in accumulated sand or grit. Follow the supplied manual’s immersion requirements and provide enough space for unrestricted float movement on automatic versions.

Use the carrying handle, or a suitable lifting rope attached to it, to position and retrieve the pump. Never lift, lower or suspend it by the electrical cable.

Connect to a correctly protected supply matching the selected pump’s voltage. Electrical installation and repairs should be carried out by a competent person.

Inspect the intake and float regularly, remove deposits and rinse the pump after use where residue could accumulate. Always disconnect the power before inspection or cleaning: the thermal protector can reset and allow the motor to restart automatically.

Important Notes

Do not operate the Mizar without water. Thermal overload protection is not a substitute for correct water-level control.

Keep the liquid temperature at or below 35°C, observe the 5-metre maximum immersion depth and protect the pump from freezing.

The operating instructions specify a maximum of 15 starts per hour. Sump capacity and float settings should prevent repeated rapid cycling.

These pumps are not recommended for ponds. Do not operate them in any pool, pond or tank while people are in the water.

Do not select the standard Mizar for seawater, fuels or chemically aggressive liquids without a specific compatibility assessment.

Why Buy from Henry Pumps?

Choose your Mizar pump with practical advice from an independent pump specialist.

Henry Pumps can help you assess the water condition, required flow, vertical lift, hose arrangement and available electrical supply, as well as whether manual or automatic operation best suits the application.

We can also help with discharge accessories, replacement parts and maintenance enquiries.

Need Help or Advice?

Tell us where the water collects, what it contains, how high it needs to be lifted and the discharge distance.

Call 0333 050 3748 or email sales@henrypumps.co.uk for help selecting your Mizar pump and accessories.

product review overlay image

Customer reviews

(1 Customer reviews)
Write a review
5 Stars
100%
4 Stars
0%
3 Stars
0%
2 Stars
0%
1 Stars
0%

Use the Mizar submersible pumps regularly on our more industrial jobs thanks to their corrosion resistance. Arrived promptly the following day from Henrys, thank you.

John Jones | Southampton | April 2019

  • Voltage:
    230v
  • Condition:
    New
  • Product Code:
    24101017
  • Weight:
    5kg
Is this the right pump for you?

Suitable for

    • Cellar & sump drainage
    • Factory & plant rooms
    • Rainwater & seepage water removal
    • Flooding & groundworks

Not suitable for

    • Sewage, wipes & fibrous waste water
    • Thick sludge & slurry
    • Seawater, fuels & aggressive chemicals
    • Pond & water feature circulation

Frequently Asked Questions

What is the difference between the Mizar 30 and Mizar 60?

The Mizar 30 has a 0.25kW motor output, a maximum flow of 150 litres per minute and a maximum head of 8 metres.

The Mizar 60 has a 0.45kW motor output, a maximum flow of 175 litres per minute and a maximum head of 10 metres.

Choose according to the required flow and total delivery head. Both models have the same 10mm free passage.

Can the Mizar pump dirty water?

The standard Mizar can be used for lightly dirty drainage water containing small suspended particles within its 10mm passage limit.

It is not suitable for thick sludge, abrasive sediment, wipes or fibrous wastewater. The type and concentration of material in the water matter—not simply whether an individual particle is smaller than 10mm.

Are the Mizar 30 and 60 available with a float switch?

Yes. Both are available in manual and automatic versions.

Automatic models include a pendant float switch for water-level-controlled starting and stopping. Manual models require operator control or a separately specified external control system.

Will an automatic Mizar fit in a narrow sump?

The pump body has a 154mm diameter, but the complete installation needs more space than this.

The pendant float must move freely beside the pump without catching on walls, cables or pipework. Check the chamber dimensions and the required switching levels before ordering; do not choose solely on the pump’s body diameter.

Can the Mizar run dry?

It should not be operated dry. Follow the supplied operating instructions and stop the pump before it runs without sufficient water.

On automatic versions, correct float positioning is essential. The thermal overload protects against overheating but should not be relied upon as low-water-level protection.

How deep can the Mizar be submerged?

The maximum immersion depth is 5 metres below the water surface.

This is different from the pump’s maximum delivery head. Cable length, immersion depth and the height to which water can be pumped are separate specifications.

Is this the same as the Mizar 316 stainless steel range?

No. This page covers the standard Mizar 30 and 60 with 304 stainless steel casing and intake components.

The Mizar/S 316 versions are separate products. For a chemically demanding application, the complete pump—including its seals and other wetted materials—must be checked against the liquid being pumped.

Henry Pumps Trade

In the trade? Unlock exclusive benefits

Support, pricing, and access tailored to pumping systems professionals.
30 day credit terms
Dedicated account manager

Buy with confidence

At Henry Pumps, we support residential, commercial, and industrial customers, from homeowners and landlords to contractors and facilities teams. Based in Derbyshire, we help solve flooding, drainage, and water management challenges across the UK. Every pump we supply is chosen for proven reliability and performance, backed by expert, straightforward advice you can trust. Whether you’re maintaining a property, managing a building, or dealing with an urgent issue, we’ll help you find the right solution.

Trusted Experts
We help you choose the right pump with honest, impartial advice every time.
Real Premises
Based in Chesterfield, UK, with a team that knows pumps inside out.
Next Working Day Delivery
Order before 4pm on in-stock items for next day delivery.
Rated 4.5/5 on Google
Based on real customer feedback.
Need help choosing a pump?
Get it right the first time. Our friendly team provides impartial, expert guidance to help you select the perfect pump.
Speak to our experts
Close
Checking availability…

Our pump experts are available Monday–Thursday 8am–5pm and Friday 8am–4pm.

Outside of these hours, please send us a message and we'll respond as soon as the team is back online. Orders can be placed through the website at any time.